 |
LH1120
Degol
| Quantity: | |
|---|---|
The DEGOL LH1120 Modern Straight Round Door Lever Handle with Sculpted Angled Transition on Round Rose is a contemporary architectural door hardware design combining a clean cylindrical gripping section with a distinctive sculpted connection between the lever and the mounting rose.
Unlike a conventional straight tubular door handle, the LH1120 features a specially shaped transition at the lever neck.
This transition combines an angled surface, a flowing curved contour, and a defined diagonal line that visually connects the round lever to its mounting base.
The result is a modern lever handle with a simple overall silhouette and a more expressive architectural detail near the rose.
The main gripping section is straight and cylindrical, with a reference diameter of 22 mm.
Its outer end has a softly rounded profile, while the inner connection introduces a sculptural design element without extending along the full length of the handle.
This contrast between a geometric straight bar and a carefully shaped connecting neck is the defining characteristic of the LH1120.
The handle is illustrated with a round rose and a satin silver metallic appearance.
The reference specification identifies zinc alloy or aluminum alloy as the material options.
Typical finish categories shown in the supplied drawing include satin nickel, polished chrome, matte black, and satin aluminum.
The actual availability of each material and finish combination must be confirmed with DEGOL.
According to the supplied reference engineering sheet, the LH1120 has a nominal lever length of 130 mm, a cylindrical grip diameter of 22 mm, and a projection of 63 mm.
The circular rose measures approximately 53 mm in diameter and 9 mm in thickness.
The mounting detail illustrates fixing centers of approximately 38 mm, while the spindle detail identifies an 8 × 8 mm square spindle with a typical illustrated length of 100 mm.
The reference door thickness range is 35–55 mm.
With its straight cylindrical grip and distinctive angled transition, the LH1120 can be considered for compatible residential interior doors, modern apartments, offices, and selected hospitality or commercial interior projects.
Jiangmen Degol Hardware Co., Ltd. welcomes inquiries from architectural hardware importers, door handle distributors, building material wholesalers, door manufacturers, contractors, and OEM / ODM customers.
Modern straight cylindrical door lever design
Distinctive sculpted angled transition
Decorative diagonal connection detail
Smooth curved neck geometry
Rounded lever-end profile
Zinc alloy or aluminum alloy material options
Approx. 130 mm reference lever length
Approx. Ø22 mm cylindrical grip
Approx. 63 mm reference projection
Approx. Ø53 mm round rose
Approx. 9 mm rose thickness
Concealed-fixing mounting concept
Approx. 38 mm fixing-center distance
Two approximately Ø4.5 mm mounting holes
Standard reference 8 × 8 mm square spindle
Approx. 100 mm typical spindle length
Reference door thickness range of 35–55 mm
Satin nickel, polished chrome, matte black, and satin aluminum finish inquiries
Suitable for evaluation in compatible interior door applications
Wholesale and OEM / ODM inquiries welcomed
Important Technical Notice: The supplied drawing states that its dimensions are typical market reference values and can be customized by project. These measurements are not independently verified LH1120 manufacturing specifications. Final dimensions, materials, finishes, mounting details, and accessories must be confirmed using approved factory documentation or physical samples.
The DEGOL LH1120 is a modern straight round lever handle design featuring a cylindrical gripping section, a sculpted angled transition near the handle neck, and a circular mounting rose.
The lever is designed around a square-spindle connection concept for operation with a compatible door latch or lock mechanism.
Its most distinctive feature is the decorative transition between the rose-mounted neck and the straight cylindrical lever.
1. Straight Cylindrical Lever
The main gripping section forms a clean horizontal round bar rather than a curved or flattened handle.
2. Sculpted Angled Transition
Near the handle base, the design incorporates an angled geometric transition that creates a visually defined connection between the neck and the straight lever.
3. Flowing Curved Neck
The angled detail is combined with rounded surfaces, creating a transition that appears sculpted rather than sharply assembled from separate rectangular parts.
4. Diagonal Design Line
The illustrated transition includes a diagonal boundary line that provides visual contrast with the straight cylindrical grip.
5. Rounded Grip Profile
The reference drawing identifies a circular cross-section measuring approximately Ø22 mm.
6. Softly Rounded Lever End
The outer end of the handle has a smooth rounded termination.
7. Round Decorative Rose
The lever is mounted on a circular rose with a reference diameter of Ø53 mm.
8. Concealed Fixing Concept
The reference sheet illustrates a rear mounting plate and identifies concealed screw, through-bolt, or self-tapping screw fixing as possible arrangements.
The final fixing configuration must be confirmed.
9. Square Spindle Connection
The reference spindle has an 8 × 8 mm square cross-section.
10. Zinc Alloy or Aluminum Alloy
Both material categories are identified in the drawing.
Many modern door handles use a simple straight cylindrical bar connected directly to a round rose.
The LH1120 retains the clean appearance of a straight bar while adding a sculptural feature at the base.
The angled transition gives the handle a distinctive visual identity without changing the straight profile of the main gripping section.
The reference sheet shows:
One straight cylindrical lever
One sculpted angled transition
One connecting neck
One round decorative rose
One rear fixing plate detail
Two mounting-hole positions
One square spindle detail
The illustration does not establish the complete contents of a commercial handle set.
A second lever, escutcheons, lock body, cylinder, screws, and other accessories must be confirmed separately.
| Parameter | Specification |
|---|---|
| Brand | DEGOL |
| Model | LH1120 |
| Product Name | Straight Round Door Lever Handle with Sculpted Angled Transition |
| Product Category | Architectural Door Hardware |
| Product Type | Door Lever Handle on Round Rose |
| Design Style | Modern / Contemporary / Geometric |
| Lever Shape | Straight Round Bar |
| Grip Cross-Section | Circular |
| Distinctive Feature | Sculpted Angled Transition |
| Connecting Neck | Curved and Angled |
| Lever End | Softly Rounded |
| Material Option 1 | Zinc Alloy |
| Material Option 2 | Aluminum Alloy |
| Material Examples in Reference | Zamak / Aluminum Alloy 6063 or 6061 |
| Illustrated Appearance | Satin Silver Metallic |
| Typical Finish Categories | Satin Nickel / Polished Chrome / Matte Black / Satin Aluminum |
| Custom Finish | Subject to Confirmation |
| Lever Length | 130 mm – Reference |
| Lever Diameter | Ø22 mm – Reference |
| Lever Projection | 63 mm – Reference |
| Rose Shape | Round |
| Rose Diameter | Ø53 mm – Reference |
| Rose Thickness | 9 mm – Reference |
| Mounting Type | Concealed Fixing – Reference |
| Mounting-Hole Spacing | 38 mm – Reference |
| Mounting Holes | 2 × Ø4.5 mm – Reference |
| Fixing Arrangements | Concealed Screw / Through-Bolt / Self-Tapping Screw; verify |
| Standard Spindle | 8 × 8 mm Square – Reference |
| Typical Spindle Length | 100 mm – Reference |
| Alternative Spindle Sections | 7 mm / 9 mm – Inquiry Only |
| Suitable Door Thickness | 35–55 mm – Reference |
| Intended Application | Compatible Interior Doors |
| Door Material | Wood / Metal, subject to compatibility |
| Reference Tolerance: ≤30 mm | ±0.2 mm |
| Reference Tolerance: >30–100 mm | ±0.3 mm |
| Reference Tolerance: >100 mm | ±0.5 mm |
| OEM / ODM | Available for Inquiry |
| Manufacturer | Jiangmen Degol Hardware Co., Ltd. |
| Country of Origin | China |
Specification Notice: The dimensions and tolerances above are transcribed from the supplied reference sheet. They are not approved production specifications for LH1120.
The LH1120 engineering reference sheet includes multiple views intended to illustrate the handle's shape and principal dimensions.
These include:
Product perspective rendering
Front view
Top view
Side view
Enlarged angled-transition detail
Lever cross-section
Round rose front view
Rose backplate mounting detail
Square spindle detail
Main dimension table
Reference dimensional tolerance table
All dimensions are expressed in millimeters.
The reference drawing identifies a lever length of 130 mm.
The front view illustrates the dimension from the lever mounting-axis area toward the outer handle end.
The exact measurement datum must be confirmed in an approved drawing.
The main lever has a reference circular cross-section of Ø22 mm.
This dimension defines the rounded gripping profile.
Unlike a flattened oval or rectangular handle, the LH1120 uses a circular bar geometry along its main gripping section.
The reference specification identifies a projection of 63 mm.
This measurement is relevant when evaluating the handle's installed position and clearance from the door face.
The final projection datum must be confirmed.
The enlarged detail illustrates a decorative transition between the mounting neck and the straight lever.
The transition incorporates:
A diagonal design boundary
A curved surface
An angled upper contour
A rounded lower connection
A gradual visual change into the cylindrical grip
This feature distinguishes LH1120 from a conventional straight tubular door handle.
The transition appears to be integrated into the lever-neck design.
The supplied drawing does not provide individual dimensions for the angled feature, such as its length, height, surface radius, or angle.
These details require an approved production drawing.
Beyond the decorative transition, the handle continues as a straight cylindrical bar.
The round cross-section is identified as Ø22 mm.
The outer end has a smooth rounded profile.
The exact end radius is not specified.
The circular rose has a reference diameter of 53 mm.
The round rose complements the cylindrical grip and curved connecting geometry.
The reference rose thickness is 9 mm.
The actual installed thickness depends on the final decorative cover and mounting assembly.
The rear mounting detail identifies a fixing-center distance of 38 mm.
This dimension must be verified before preparing the door.
The reference rear plate shows two approximately Ø4.5 mm mounting holes.
The final hole dimensions and fixing method may differ according to the approved mounting system.
The reference sheet identifies concealed screw, through-bolt, and self-tapping screw arrangements as potential fixing methods.
These should be treated as configuration possibilities rather than confirmed included hardware.
The reference spindle detail identifies an 8 × 8 mm square cross-section.
Compatibility with the selected latch or mortise lock must be confirmed.
The drawing illustrates a typical spindle length of 100 mm.
The final supplied length must suit the door thickness, handle assembly, and selected lock.
The product features mention optional 7 mm or 9 mm square spindle configurations.
These are inquiry options only and must not be assumed to be available for every LH1120 version.
The reference drawing identifies a suitable door thickness range of 35–55 mm.
Actual compatibility depends on the fixing arrangement, spindle, lock, and approved product design.
The drawing provides the following general reference tolerance schedule:
| Dimension Range | Reference Tolerance |
|---|---|
| ≤30 mm | ±0.2 mm |
| >30–100 mm | ±0.3 mm |
| >100 mm | ±0.5 mm |
These values are not independently verified manufacturing acceptance criteria.
| Component | Reference Dimension |
|---|---|
| Lever Length | 130 mm |
| Grip Diameter | Ø22 mm |
| Projection | 63 mm |
| Rose Diameter | Ø53 mm |
| Rose Thickness | 9 mm |
| Fixing-Center Spacing | 38 mm |
| Mounting Holes | 2 × Ø4.5 mm |
| Square Spindle | 8 × 8 mm |
| Typical Spindle Length | 100 mm |
| Door Thickness Range | 35–55 mm |
| Transition Angle | Not Specified |
| Transition Radius | Not Specified |
| Rounded Tip Radius | Not Specified |
| Final Manufacturing Tolerances | To Be Confirmed |
The engineering sheet expressly describes these dimensions as typical market reference data for this style.
The final LH1120 geometry may differ.
Request an approved technical drawing or physical sample before manufacturing, drilling, installation, or bulk purchasing.
Zinc alloy is one of the material options identified in the LH1120 reference sheet.
Zinc alloys are used in a variety of decorative architectural hardware products.
Depending on the selected alloy grade and manufacturing process, zinc alloy can support detailed decorative shapes such as the sculpted transition shown on LH1120.
Potential design considerations include:
Decorative angled transition geometry
Smooth cylindrical gripping section
Rounded connecting surfaces
Metallic surface finishing
Compatible interior door applications
The reference sheet mentions Zamak as a typical zinc alloy example.
This does not establish the exact alloy grade used for LH1120.
Aluminum alloy is the second material category identified in the reference drawing.
Aluminum alloys generally have lower density than zinc alloys.
Depending on the alloy grade and manufacturing process, aluminum alloy may be suitable for modern architectural hardware with clean cylindrical geometry.
The drawing mentions aluminum alloy grades 6063 and 6061 as examples.
These grades should not be treated as verified LH1120 production materials.
Potential design considerations include:
Straight cylindrical gripping section
Contemporary geometric styling
Lower-density material selection
Satin metallic appearance
Compatible interior door applications
The production process and feasibility of the sculpted angled transition must be confirmed for the selected alloy.
| Feature | Zinc Alloy | Aluminum Alloy |
|---|---|---|
| Material Category | Zinc-Based Alloy | Aluminum-Based Alloy |
| Typical Density | Higher | Lower |
| Straight Round Lever Geometry | Possible | Possible |
| Sculpted Transition Geometry | Process-Dependent | Process-Dependent |
| Decorative Finish Options | Alloy and Process-Dependent | Alloy and Process-Dependent |
| Product Weight | Construction-Dependent | Construction-Dependent |
| Mechanical Performance | Grade-Dependent | Grade-Dependent |
| Corrosion Resistance | Alloy and Coating-Dependent | Alloy and Coating-Dependent |
The appropriate material should be selected according to the intended application, performance requirements, finish, budget, and production feasibility.
Satin nickel is one of the typical finish categories listed in the reference drawing.
Its soft metallic appearance can complement the LH1120's straight cylindrical grip and sculpted transition.
Polished chrome is another listed finish category.
A reflective chrome appearance can emphasize the contrast between the cylindrical bar and the decorative connecting geometry.
Matte black is identified as a typical finish category.
Customers may inquire about this appearance for minimalist or contemporary interior hardware projects.
Satin aluminum is also listed in the supplied reference sheet.
The actual surface treatment depends on the selected base material and manufacturing process.
Customers may inquire about additional finishes, colors, or textures.
Custom finish requests are subject to technical feasibility, material compatibility, sample approval, and commercial terms.
The illustrated product shows satin silver metallic surfaces with reflective highlights near the mounting neck.
These highlights do not independently establish a specific coating process or a verified multi-tone finish.
Before confirming an order, buyers should verify:
Base material
Exact alloy grade
Surface preparation
Finish type
Finish color
Coating process
Surface texture
Corrosion-resistance requirements
Cleaning and maintenance requirements
Finish approval sample
Material Notice: LH1120 is presented as a zinc alloy or aluminum alloy door lever handle. Stainless steel is not identified as a material option in the supplied drawing.
The DEGOL LH1120 can be considered for modern interior architectural projects where a straight cylindrical lever with a distinctive decorative connection is desired.
The straight round lever and sculpted angled transition can complement contemporary residential interiors.
LH1120 may be considered for compatible bedroom doors when paired with an appropriate latch or privacy lock.
Its geometric design can coordinate with minimalist or modern interior door styles.
The cylindrical grip and decorative transition offer a contemporary appearance for home workspaces.
The handle may be evaluated for residential apartment and condominium interior door schedules.
LH1120 may suit compatible office doors, meeting rooms, and administrative interiors.
The design may be considered for selected hotel interior applications when the final product meets the project's required operating, locking, and durability specifications.
The handle provides a more decorative alternative to a conventional plain round-bar lever.
Door manufacturers may evaluate LH1120 for compatible door constructions and lock systems.
The straight cylindrical grip and sculpted angled transition create a recognizable product design for hardware distributors and importers.
| Door Type | Application Consideration |
|---|---|
| Wooden Interior Doors | Subject to fixing and lock compatibility |
| MDF Interior Doors | Subject to door construction |
| Composite Interior Doors | Subject to approved installation requirements |
| Bedroom Doors | Compatible latch or privacy lock required |
| Apartment Interior Doors | Suitable for evaluation |
| Office Interior Doors | Suitable for evaluation |
| Meeting Room Doors | Subject to lock requirements |
| Hotel Interior Doors | Project performance requirements must be verified |
| Metal Interior Doors | Appropriate fixing preparation required |
| Commercial Interior Doors | Subject to project requirements |
| Exterior Entrance Doors | Environmental suitability not established |
| Fire-Rated Doors | Requires appropriate certification and approval |
| Frameless Glass Doors | Direct compatibility not established |
| Sliding Doors | Not intended as a conventional sliding-door pull |
Before selecting LH1120, confirm:
Door material
Door thickness
Latch or mortise lock type
Spindle section
Spindle length
Fixing-center spacing
Mounting-hole dimensions
Lever handing
Lever operating clearance
Required finish
Applicable project performance standards
The reference drawing does not establish fire rating, emergency-exit suitability, accessibility compliance, or certification for a specific door assembly.
The following installation sequence is a general guide only.
Actual installation must follow the approved LH1120 instructions and the selected latch or lock manufacturer's requirements.
Check the door material, thickness, and lock preparation.
The reference drawing identifies a door thickness range of 35–55 mm.
Inspect the delivered components against the confirmed packing list.
Do not assume that a pair of levers, spindle, screws, lock body, or escutcheons is included unless specified.
Verify lever orientation, handing, and the required installation arrangement.
The supplied drawing does not establish whether every production version is reversible.
Mark the spindle opening and mounting positions using the approved installation template.
Do not drill directly from the reference engineering illustration.
Fit the selected latch or mortise lock according to its installation instructions.
The reference sheet identifies an 8 × 8 mm square spindle with a typical illustrated length of 100 mm.
Confirm that the actual spindle matches the lock and door thickness.
Align the lever and its sculpted transition in the required orientation.
Check the straight cylindrical grip for correct positioning.
Fit the mounting components according to the approved fixing method.
The reference drawing shows approximately 38 mm fixing centers and two Ø4.5 mm mounting holes.
The actual dimensions must be confirmed before drilling.
Fit the circular rose cover using the approved assembly method.
Check:
Lever alignment
Smooth operating movement
Correct latch retraction
Secure mounting
Spindle engagement
Adequate hand clearance
Correct lever return where applicable
No interference with adjacent hardware
Correct lock operation where applicable
Mounting screws, spindle dimensions, fixing centers, and door thickness compatibility must be confirmed using approved technical documentation.
The angled connection gives LH1120 a recognizable architectural design feature.
The main gripping section maintains a simple straight round-bar profile.
The design combines a clean cylindrical lever with a decorative curved and angled neck.
The reference Ø22 mm circular grip creates a smooth, rounded appearance.
The outer end avoids the appearance of a sharply squared termination.
Zinc alloy provides one material category for customers evaluating decorative architectural hardware.
Aluminum alloy provides another material category for contemporary interior door hardware projects.
The approximately Ø53 mm reference rose coordinates with the handle's cylindrical geometry.
The reference mounting design supports a clean appearance when the appropriate concealed-fixing configuration is used.
The reference sheet lists satin nickel, polished chrome, matte black, and satin aluminum.
LH1120 may be considered for compatible residential, apartment, office, and hospitality interior doors.
The design provides a basis for discussions about materials, finishes, branding, packaging, and project-specific modifications.
The sculpted angled transition distinguishes LH1120 from ordinary straight tubular lever handles.
Jiangmen Degol Hardware Co., Ltd. welcomes OEM and ODM inquiries involving modern architectural door handle designs, including LH1120.
Customers may submit reference drawings, samples, material requirements, finish specifications, branding artwork, and packaging requirements for evaluation.
Potential private-label requirements include:
Customer logo identification
Custom model numbers
Product labels
Barcode stickers
Branded packaging
Printed installation instructions
Export carton markings
Customers may inquire about:
Zinc Alloy
Aluminum Alloy
The final material grade, construction, and production process must be confirmed.
The reference drawing identifies:
Satin Nickel
Polished Chrome
Matte Black
Satin Aluminum
Additional finish requests can be evaluated separately.
Potential custom design inquiries include:
Transition angle
Diagonal design line
Neck contour
Curved connection profile
Surface radius
Transition length
Decorative surface treatment
These features may require revised tooling or an approved production drawing.
Customers may inquire about:
Overall lever length
Grip diameter
Lever-end profile
Projection
Lever orientation
Surface texture
Potential requests include:
Rose diameter
Rose thickness
Decorative cover profile
Mounting arrangement
Fixing-hole positions
Customers may submit specific spindle and lock compatibility requirements.
The reference sheet identifies an 8 mm square spindle and mentions optional 7 mm and 9 mm sizes.
Actual availability must be confirmed.
Potential packaging requests include:
Private-label boxes
Protective inner packaging
Printed labels
Barcode identification
Customized installation sheets
Export carton markings
Buyers may submit door schedules, architectural drawings, material requirements, and estimated quantities.
Where available, samples may be requested to confirm:
Actual material
Product dimensions
Sculpted transition geometry
Finish color and texture
Mounting arrangement
Spindle compatibility
Product appearance
Packaging configuration
OEM / ODM Notice: All customization requests are subject to technical feasibility, tooling requirements, MOQ, sample approval, and agreed commercial terms.
| Item | Information |
|---|---|
| Product Model | LH1120 |
| Brand | DEGOL |
| Product Name | Straight Round Door Lever Handle with Sculpted Angled Transition |
| Material Options | Zinc Alloy or Aluminum Alloy |
| Exact Alloy Grade | To Be Confirmed |
| Illustrated Appearance | Satin Silver Metallic |
| Typical Finish Inquiries | Satin Nickel / Polished Chrome / Matte Black / Satin Aluminum |
| Round Rose | Illustrated; Package Quantity TBC |
| Square Spindle | 8 × 8 mm Reference |
| Typical Spindle Length | 100 mm Reference |
| MOQ | Subject to Quotation |
| Sample Availability | On Request |
| OEM Packaging | Subject to Confirmation |
| Production Lead Time | Subject to Order Confirmation |
| Payment Terms | To Be Negotiated |
| Shipping Terms | Subject to Quotation |
| Manufacturer | Jiangmen Degol Hardware Co., Ltd. |
| Country of Origin | China |
Step 1 – Submit Your Inquiry
Provide model LH1120, estimated order quantity, preferred material, required finish, and destination country.
Step 2 – Confirm the Material
Specify whether the requested configuration should use zinc alloy or aluminum alloy.
Step 3 – Confirm the Finish
Select the required finish and request confirmation of production availability.
Step 4 – Verify the Technical Specifications
Request approved dimensions, mounting details, spindle specifications, and lock compatibility information.
Step 5 – Request Samples
Contact DEGOL regarding sample availability, pricing, and shipping arrangements.
Step 6 – Confirm OEM / ODM Requirements
Submit branding, packaging, or custom drawing requirements where applicable.
Step 7 – Review the Wholesale Quotation
Confirm unit pricing, MOQ, lead time, payment terms, and shipping arrangements.
Step 8 – Approve the Product Configuration
Review approved specifications and physical samples where required.
Step 9 – Arrange Production and Delivery
Production and shipment follow the confirmed purchase order and agreed commercial terms.
Product Model: LH1120
Required Order Quantity
Preferred Material: Zinc Alloy or Aluminum Alloy
Required Surface Finish
Door Thickness
Lock and Spindle Requirements
Mounting Method
Required Package Contents
OEM / ODM Requirements
Packaging Preferences
Destination Country
Expected Delivery Schedule
Jiangmen Degol Hardware Co., Ltd. serves international architectural hardware customers and welcomes wholesale and OEM / ODM inquiries involving door handles and related hardware.
The LH1120 design can be discussed with DEGOL for material selection, technical verification, finish options, and project-specific requirements.
Customers may inquire about:
Zinc alloy door handles
Aluminum alloy door handles
Straight cylindrical door levers
Modern decorative door handles
Round rose door handles
Interior door hardware
Door escutcheons
Door locks and mortise lock bodies
Door hinges
Related architectural door accessories
Specific product availability must be confirmed.
DEGOL welcomes discussions involving customer drawings, reference samples, material requirements, and project specifications.
Custom product development is subject to technical evaluation.
For LH1120, buyers may inquire about zinc alloy and aluminum alloy configurations.
The exact alloy grade, construction, and manufacturing process require confirmation.
The supplied drawing lists satin nickel, polished chrome, matte black, and satin aluminum as typical finish categories.
Buyers may discuss specific finish colors, textures, and performance requirements.
For LH1120, customers may request:
Approved technical drawings
Verified lever dimensions
Confirmed alloy specifications
Sculpted transition geometry
Rose dimensions
Mounting details
Spindle specifications
Door thickness compatibility
Finish information
Packaging specifications
Buyers may request information about inspection procedures covering:
Dimensional consistency
Surface appearance
Lever alignment
Transition geometry
Mounting fit
Spindle compatibility
Handle operation
Packaging condition
LH1120-specific test reports, certifications, and performance ratings must be verified separately.
International customers may submit requests involving:
Material selection
Lever geometry modifications
Surface finish customization
Private-label branding
Customized packaging
Project-specific mounting requirements
DEGOL welcomes inquiries from:
Architectural hardware importers
Door handle wholesalers
Hardware distributors
Door manufacturers
Building material suppliers
Construction contractors
Hospitality project purchasing teams
International hardware brands
OEM / ODM customers
Factory Capability Notice: General supplier information does not establish the production capacity, exact manufacturing process, certification, or availability of every LH1120 configuration. Model-specific details must be confirmed with DEGOL.
The DEGOL LH1120 is a modern straight round door lever handle featuring a sculpted angled transition and a circular mounting rose.
The supplied reference sheet identifies zinc alloy or aluminum alloy as the material options.
Zinc alloy is listed as a material option. Actual production availability and alloy grade must be confirmed with DEGOL.
Aluminum alloy is also identified as a material option. The final production configuration requires confirmation.
The supplied drawing identifies zinc alloy or aluminum alloy, not stainless steel.
Zinc alloys generally have higher density than aluminum alloys. Mechanical performance, corrosion resistance, and finish compatibility depend on the exact grade and manufacturing process.
The most suitable material depends on the required performance, product weight, finish, budget, and intended application.
LH1120 has a modern geometric design featuring a straight cylindrical lever and a decorative angled transition.
The main gripping section is straight. The connecting neck incorporates curved and angled sculptural details.
Its distinctive feature is the sculpted angled transition between the mounting neck and the straight cylindrical grip.
The reference drawing identifies a lever length of 130 mm.
The reference cylindrical grip diameter is Ø22 mm.
The reference projection is 63 mm.
The main grip is round, with a reference circular cross-section of Ø22 mm.
It is the decorative connection between the lever neck and cylindrical gripping section, featuring an angled surface and curved contour.
The supplied drawing does not specify the exact transition angle.
The reference drawing does not provide a verified transition radius.
Yes. The illustration shows a softly rounded outer end.
The drawing does not establish whether the handle is solid or hollow.
Yes. The product is illustrated with a circular mounting rose.
The reference rose diameter is Ø53 mm.
The reference rose thickness is 9 mm.
The reference drawing identifies concealed fixing as a mounting concept. The actual fixing arrangement must be confirmed.
The rear mounting detail indicates approximately 38 mm between fixing centers.
The reference drawing shows two approximately Ø4.5 mm mounting holes.
The standard reference spindle section is 8 × 8 mm square.
The supplied drawing illustrates a typical spindle length of 100 mm.
The reference sheet mentions optional 7 mm and 9 mm spindle sizes. Actual availability must be confirmed.
The reference specification identifies a door thickness range of 35–55 mm.
Yes. The design may be considered for compatible interior door applications.
It may be considered for compatible wooden interior doors when the fixing system and lock mechanism are suitable.
Metal door compatibility depends on the door construction, fixing method, and lock configuration.
LH1120 may be considered for compatible office interior doors.
The design can be evaluated for hospitality interiors, subject to the project's durability, security, and locking requirements.
Exterior suitability has not been established. Material, finish, corrosion resistance, and environmental exposure requirements should be reviewed.
No LH1120 fire-rating documentation has been provided.
The reference drawing lists satin nickel, polished chrome, matte black, and satin aluminum as typical finish categories. Actual availability must be confirmed.
Satin nickel is listed as a typical finish category. Customers should confirm availability for the selected material.
Polished chrome is listed in the reference specification. Production availability requires confirmation.
Matte black is identified as a typical finish category. The final finish configuration should be confirmed.
Satin aluminum is listed as a typical finish option. The actual surface treatment depends on the selected material and production process.
Customers may submit custom finish requests for technical and commercial evaluation.
The rendering shows different metallic highlights, but it does not independently establish a verified two-tone production finish.
The supplied drawing does not illustrate keyhole escutcheons. Their inclusion or availability must be confirmed.
The reference sheet does not establish that a mortise lock body is included.
Only one lever is illustrated. The standard commercial package quantity must be confirmed.
The supplied reference sheet does not specify a return spring mechanism.
Handing and reversibility are not established by the supplied drawing. Buyers should verify the actual configuration.
LH1120 has a straight Ø22 mm cylindrical grip and a sculpted angled transition near the base.
LH1119 has a flowing curved lever with a reference grip diameter of Ø19.5 mm.
Their primary difference is the lever shape and connecting geometry.
LH1120 uses a round Ø22 mm cylindrical grip with a distinctive angled transition.
LH1118 uses a flattened round-bar profile with a reference cross-section of 22 × 12 mm.
Both designs have straight round gripping sections, but LH1120 features a prominent sculpted angled transition at the lever base.
LH1051 is illustrated with a simpler straight cylindrical lever and neck connection.
Customers may submit custom transition geometry requirements for technical evaluation. Changes may require revised drawings and tooling.
DEGOL welcomes inquiries about private-label branding and customized packaging.
Customers may contact DEGOL to inquire about sample availability, pricing, and shipping arrangements.
The confirmed MOQ has not been provided. It should be requested according to the material, finish, and packaging requirements.
No. The supplied dimensions are typical market reference values and must not be used as approved manufacturing or drilling specifications.
Buyers may request verified dimensions and approved technical documentation from DEGOL.
DEGOL welcomes wholesale inquiries from architectural hardware importers, distributors, door manufacturers, and professional buyers.
Customers may submit OEM / ODM requirements for technical and commercial evaluation.
Contact DEGOL through WhatsApp at +86 13725946499 or email info@degolhardware.com.
Provide the model number, preferred material, finish, order quantity, and destination country.
Looking for a modern straight round door lever handle with a distinctive sculpted angled transition, zinc alloy or aluminum alloy material options, and a round concealed-fixing rose?
Contact DEGOL Hardware for confirmed product specifications, approved technical drawings, material information, available finishes, sample details, OEM / ODM requirements, packaging options, and wholesale pricing.
Product Model: LH1120
Product Name: DEGOL LH1120 Modern Straight Round Door Lever Handle with Sculpted Angled Transition on Round Rose – Zinc Alloy or Aluminum Alloy
Material Options: Zinc Alloy or Aluminum Alloy
Typical Finish Inquiries: Satin Nickel, Polished Chrome, Matte Black, Satin Aluminum
Company: Jiangmen Degol Hardware Co., Ltd.
WhatsApp: +86 13725946499
Website: https://www.degolhardware.com/
Email: info@degolhardware.com
Request Your LH1120 Zinc Alloy or Aluminum Alloy Straight Round Door Lever Handle Wholesale Quote Today
